Kartro Prefabrik Ev Hattı
Düşük fiyattan ekipman satın almaya karar verirseniz gerçek satıcı ile iletişime geçtiğinizden emin olun. Ekipmanın sahibi hakkında bulabildiğiniz kadar çok bilgi edinmeye çalışın. Hile yapmanın bir yolu da kendinizi gerçek bir şirket olarak göstermektir. Şüpheye düşmeniz halinde, geribildirim formu üzerinden ek kontrol yapmamız için bizi bilgilendirin.
Bir satın alma yapmaya karar vermeden önce seçtiğiniz ekipmanın ortalama fiyatını anlamak için çeşitli satış tekliflerini dikkatli bir şekilde inceleyin. Beğendiğiniz teklifin fiyatı benzerlerinden çok daha düşükse biraz düşünün. Önemli bir fiyat farkı gizlenen kusurların veya satıcının dolandırıcılık yapma çabasının bir göstergesi olabilir.
Benzer ekipman için ortalama fiyattan çok farklı fiyattaki bir ürünü satın almayın.
Şüpheli güvencelere ve ön ödemeli ürünlere onay vermeyin. Şüpheye düşmeniz halinde, ayrıntıları netleştirmekten çekinmeyin, ilave fotoğraflar ve ekipmanın belgelerini isteyin, belgelerin orijinalliğini kontrol edin, soru sorun.
En yaygın dolandırıcılık biçimi. Hileci satıcılar bir ekipmanı satın alma hakkınızı “ayırtmak” için belirli bir miktar peşin ödeme talep edebilir. Böylelikle dolandırıcılar yüksek miktarda para toplayıp ortadan kaybolabilirler, bir daha iletişime geçemezsiniz.
- Ön ödemenin karta transferi
- İletişim sırasında satıcı şüphe uyandırıyorsa para transferi işlemini doğrulayan belgeler olmadan peşin ödeme yapmayın.
- “Emanetçi” hesabına transfer
- Bu tür bir istek sizi harekete geçirmelidir, büyük ihtimalle bir dolandırıcı ile iletişim kuruyorsunuz.
- Benzer isimdeki bir şirket hesabına transfer
- Dikkatli olun, dolandırıcılar, adda küçük değişiklikler yaparak kendilerini iyi bilinen şirketler gibi göstermeye çalışabilir. Şirket adı şüpheliyse para transferi yapmayın.
- Gerçek bir şirketin faturasına kendi bilgilerini yerleştirme
- Bir transfer gerçekleştirmeden önce, belirtilen detayların doğru olduğundan ve belirtilen şirketle ilişkili olduğundan emin olun.
+358 50 02...
+358 50 0264325
Production line for floor and intermediate floor structures in wood, which has been in use for 10 years for modular house manufacturing / volume house manufacturing.
Production line for floor blocks:
Station 1: Fixing station for manufacturing the frame structure, gluing, and nailing of the deck.
The station is designed for floor blocks with dimensions of 12,500 x 4,300 mm and is not adjustable in width.
The station has 5 transverse C-rails with manually adjustable fixing stops for 8 beams.
The station is equipped with 5 transverse roller conveyors that are pneumatically adjustable in height for transport to station 2. The C-rails and roller conveyors are manually movable sideways.
Nailing portal for Station 1.
The nailing portal runs on a rack rail mounted on the station.
The portal should be equipped with 8 nail guns for longitudinal nailing (nail guns removed = not included). The nail guns are adjustable sideways (for different spacing).
For cross-nailing in the floor structure, the portal is equipped with a motorized carriage with 1 nail gun (nail gun removed = not included).
The portal is equipped with a glue unit (10 l tank) and 9 glue nozzles for automatic application of glue. The glue nozzles are mounted together with the respective nail guns. The portal applies glue in one direction and nails on the return after sheet application.
On the transverse nailing cart, a panel saw is mounted. The saw is pneumatically pivotable by 90 degrees.
The saw is cranked across the floor block in the transverse direction and locked in position for longitudinal cutting. The saw is equipped with protection and a connection for extraction (dust extraction not included).
On both sides of the station, there are two outlets for air and electricity for hand tools in the station's underframe.
The operator follows the portal, standing on a motorized platform, and during longitudinal nailing, signals are received from pre-set firing stops. When nailing short beams, the operator stops the portal and starts the nailing carriage for crosswise nailing. Manual nail firing is also possible.
Station 2: Workstation and first turning section.
Manual workstation.
The station is equipped with 5 transverse, non-driven roller conveyors. The conveyors are movable sideways.
Hydraulic tilting of the station for turning the block over to station 3. Two outlets for air and electricity for hand tools in the station's underframe.
Station 3: Workstation and second turning section.
Manual workstation.
Hydraulic tilting and reception of the block from station 2.
The station is equipped with 5 transverse, non-driven roller conveyors. The conveyors are movable sideways. On both sides of the station, there are two outlets for air and electricity for hand tools in the station's underframe.
The floor block is transported on the roller conveyors back to station 2 for insulation and other processes.
The station is mobile and movable by motor sideways approximately 5 m.
Production line for intermediate floor structures:
Station 1: Fixing station for manufacturing the frame structure.
The station is designed for element sizes of 12,500 mm x 4,300 mm and is not adjustable in width.
The table has pneumatic alignment and locking from one side.
The table has 2 longitudinal C-profiles with manually adjustable fixing angles for transverse floor beams.
Hydraulic tilting of the station for turning over to station 2. Manual placement and nailing of ceiling panels.
Station 2: Workstation and turning section.
The station has pneumatic alignment from one side.
Hydraulic tilting of the station for receiving the block.
The table is covered with a plywood sheet.
The station is mobile and movable approximately 5 m.
Nailing portal and transport cart for station 1.
The nailing portal runs on a rack rail mounted on the station.
On top of the portal, there is a non-driven roller conveyor for storing cross beams, from which operators take and place them in the fixing angles.
The portal is driven by a frequency-controlled electric motor, which the operator controls with a joystick. The operator can stand on a platform that follows during nailing.
The portal is equipped with 2 x 2 nail guns (nail guns removed = not included) in a horizontal position on each side of the portal for nailing the cross beams.
The nailing portal nails with a spacing determined by pre-set stops, with the possibility of manual firing.
Nailing portal for station 2.
The nailing portal is motorized and runs on a rack rail recessed in the floor.
The portal is equipped with 2 carriages, each with one nail gun (nail guns removed = not included), running transversely to the floor structure for nailing in the transverse beams.
The carriages are also equipped with glue nozzles with accessories for applying glue to the beams.
The glue nozzles are mounted together with the respective nail guns.
The portal is equipped with a transverse saw that is pneumatically pivotable by 90 degrees. The saw is equipped with protection and a connection for dust extraction (dust extraction not included).
The operator follows the portal during nailing/gluing and stops it at each beam. The portal is driven by a frequency-controlled electric motor, which the operator controls with a joystick. The operator can stand on a platform that follows during nailing.
The portal nails transversely with spacing determined by pre-set stops. Manual firing is possible. The cross-cut saw can be motor-driven across the block. The operator locks it in the desired position for longitudinal cutting. The nailing portal follows when the station moves sideways.